how do i take off my doors on my fiesta
cheers rob

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

undo bolts between the door, and the car. Would be my guess

_________________

bolts they are pins arnt they

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

Guess! I don't have one to look and help anymore Knock the pins out with a hammer?

_________________

tryed that and they ant moving

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

had the same problem with my old pug and I used a screwdriver and a hammer, maybe theres a clip or something holding it in place that needs removing? someone on here might know.

_________________

its your luck i have a haynes manuel nest to me

1. open door and detach the door aperture weatherseal from around the hinge area.

2. Remove the screw securing the door check arm to the body.

3. Squeeze the ears together on the electrical multiplug and withdraw it from its body location on the A pillar, as applicable. Disconnect multiplug.

4. Using a screwdriver, remove the door hinge pin retaining clips from the top of both hinges, by levering them off.

5. Ford dealers use a special tool for removing door hinge pins. if this is not available, it is possible to fabricate an alternative. Engage
the special tool, then strike the main body of the tool with a soft-faced hammer to extract the lower hinge pin from its location.

6. With help the help of an assistant to support the door, remove the upper hinge pin from its location, in a similar manner to that
used for the lower hinge pin, and remove the door assemble.

Hope that helps, there is an illistration for the tool in section 5 but im sure if you google image it you will see what it looks like

ow cheers what pages is that on i have the one on my pc and teh book n cnt find any think lol io need to look harder

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

did it look ike this

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

Oh crap i forgot to check what page, its a whole section about removing/fitting body parts. I dont think that looks like it, i will find a pic for you.

ow cheers bud

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

Btw the pic of the tool you have put up thete looks more like what yoy usr the get the clip off to remove the window winders

Yeah that is a clip remover.

The best alternative to the tool described is a spanner. 11mm, thin but strong. Needs to be long too, which is incredibly rare. Then bash like a madman with a hammer. After removing the clip at the other end of course.

Other methods are heating and using a chisel to knock off the head then using a punch to push the pin through. Obviously this method needs you to replace the pin, lol.

_________________

the pins can be and usually are a right wanker to get out. ive got a tool in my collection for getting them out now...a foot of 1" x 1" x 1/8th box section with a gusseted angle on the end with a slot in. guy i used to work with made it when the car was being caged.. along with a coulple of other bits

Jam.

sound so just wack them one

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

why do you need them off?

_________________

well i dnt know if i will untill the rain stops because i fitted sill covers i filled over the welds when i smoothed them out
and neet to know if the xr2i kit will fit under the door or i needd to sand down more but it i trickky to get in the gap lol

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/

the skirts should just rivet onto the top part of the sill on the inside of the doors.

_________________

ow lol but i have filled over the welds and did not knon off i had sanded it down right if you get my jift lol

_________________


RUST IS LIGHTER THAN CARBON FIBER

http://www.fiesta-si.com
http://www.fiestaguides.co.uk/