| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| New plates and half a 2i kit https://www.fiesta-si.com/forums/viewtopic.php?f=5&t=2233 |
Page 1 of 1 |
| Author: | MallardSi [ Sun Feb 05, 2006 4:43 pm ] |
| Post subject: | New plates and half a 2i kit |
Got some old mallard green paint, from a lad i met in halfords with an Si, i need a new back arch piece because its twisted and split so no good, but i managed to do the front 2 pieces, the paints fucked though, all sandy bits in it 
Still looks good though for a botch job... will get more paint and do the rest in the summer. 
|
|
| Author: | Joe_R [ Sun Feb 05, 2006 5:13 pm ] |
| Post subject: | |
| Author: | RoryT [ Mon Feb 06, 2006 1:06 am ] |
| Post subject: | |
| Author: | onslack [ Mon Feb 06, 2006 8:58 am ] |
| Post subject: | |
looking good mate |
|
| Author: | MallardSi [ Mon Feb 06, 2006 3:49 pm ] |
| Post subject: | |
| Author: | fiestasiphil [ Mon Feb 06, 2006 8:34 pm ] |
| Post subject: | |
| Author: | Joe_R [ Mon Feb 06, 2006 9:52 pm ] |
| Post subject: | |
| Author: | MallardSi [ Tue Feb 07, 2006 10:23 pm ] |
| Post subject: | |
| Author: | ~joeboifiesta~ [ Wed Feb 08, 2006 12:06 am ] |
| Post subject: | |
| Author: | scott_si [ Wed Feb 08, 2006 10:10 pm ] |
| Post subject: | |
| Author: | MallardSi [ Thu Feb 09, 2006 8:05 am ] |
| Post subject: | |
Theres normally a small cable tie that holds the middle together but its so low it scrapes and busts off after a while, that was a rush job, before i ripped it off the first time it fitted better. Lowered 60mm on Gmax springs and shocks, with 1 and half coils cut off the back springs as its arse was and still is in the air, will lop another coil or a half off depending on how the mondeo 16s sit. Cheers |
|
| Author: | Mattyboy Esq [ Thu Feb 09, 2006 12:53 pm ] |
| Post subject: | |
| Author: | MallardSi [ Thu Feb 09, 2006 5:52 pm ] |
| Post subject: | |
| Author: | GregA [ Fri Feb 10, 2006 2:03 pm ] |
| Post subject: | |
| Author: | MallardSi [ Fri Feb 10, 2006 3:22 pm ] |
| Post subject: | |
| Author: | Paul [ Sat Feb 11, 2006 7:47 pm ] |
| Post subject: | |
| Author: | MallardSi [ Sat Feb 11, 2006 10:01 pm ] |
| Post subject: | |
Its where the jacking point cover is, its been glued before but split again, so when you straight it out to put it on the rear arch the middle bit to the right of the jacking point cover sticks out 
No point in fibreglassing the laguna splitter, its flexible and the middle would just crack
|
|
| Author: | whittyturbo [ Sun Feb 12, 2006 4:44 pm ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|