Ive got a 2.0 one ive attempted to fit, raced some shitbox fiesta earlier and that was a 2.0 an all, he said you need to use the ISCV from the car you got the MAF and ECU from, well thats long gone bye byes !
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| Cutting out when dropping the clutch? https://www.fiesta-si.com/forums/viewtopic.php?f=4&t=2748 |
Page 1 of 1 |
| Author: | MallardSi [ Mon May 08, 2006 11:33 pm ] |
| Post subject: | Cutting out when dropping the clutch? |
| Author: | Percy [ Tue May 09, 2006 12:10 am ] |
| Post subject: | |
| Author: | jdfiesta [ Tue May 09, 2006 1:42 am ] |
| Post subject: | |
| Author: | MallardSi [ Tue May 09, 2006 4:05 pm ] |
| Post subject: | |
Ive got a 2.0 one ive attempted to fit, raced some shitbox fiesta earlier and that was a 2.0 an all, he said you need to use the ISCV from the car you got the MAF and ECU from, well thats long gone bye byes !
|
|
| Author: | Paul [ Tue May 09, 2006 6:49 pm ] |
| Post subject: | |
so a 2L iscv rather than a 1.6 version |
|
| Author: | MallardSi [ Tue May 09, 2006 10:50 pm ] |
| Post subject: | |
Indeed and he said get a 2.0 lamba aswell, mind you since ive fitted the cat back on ive been getting between 80 - 100 miles out of 20.00 of normal unleaded which is better than what it used to do which was around 55 - 65 ish 
|
|
| Author: | jdfiesta [ Wed May 10, 2006 12:56 am ] |
| Post subject: | |
| Author: | Mouse [ Wed May 10, 2006 11:18 pm ] |
| Post subject: | |
iscv or have u got a aftermarket chip on in if so take it out n c if that works, whats it like going up in the engine revs when ur trundeling along? |
|
| Author: | MallardSi [ Thu May 11, 2006 1:05 am ] |
| Post subject: | |
It picks up fine when im going, but at standstill its really slow at revving up, it used to rev up and redline really fast when i first put the 2.0 in in february. ISCV is an RS1800 item. |
|
| Author: | jdfiesta [ Thu May 11, 2006 8:57 am ] |
| Post subject: | |
have you checkecked hoses for air leak? JJ |
|
| Author: | MallardSi [ Fri May 12, 2006 1:53 am ] |
| Post subject: | |
| Author: | jdfiesta [ Fri May 12, 2006 10:57 am ] |
| Post subject: | |
| Author: | Paul [ Fri May 12, 2006 7:48 pm ] |
| Post subject: | |
aye, gearbox or clutch when the revs dont pick up with speed equally, out of interest: hows best to get the iscv off an si inlet manifold? seems a bit of a cunt to get to the bottom screw/bolt? or do you remove the bit it houses into aswell?? |
|
| Author: | MallardSi [ Sat May 13, 2006 12:46 pm ] |
| Post subject: | |
Its just 2 screws paul, think you have to use a stubby screwdriver. 
|
|
| Author: | Paul [ Sun May 14, 2006 3:29 pm ] |
| Post subject: | |
yeah i know its two screws but fooked if my hands can get into that tight gap.. (talking about the car.) will have to get mi mirror out onto it |
|
| Author: | happypaul [ Sun May 14, 2006 10:38 pm ] |
| Post subject: | Re: Cutting out when dropping the clutch? |
| Author: | s.p.d. [ Sun May 21, 2006 9:55 pm ] |
| Post subject: | |
| Author: | MallardSi [ Mon May 22, 2006 12:16 am ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|