longer ones
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| efi inlet onto zetec head, bolts too short. https://www.fiesta-si.com/forums/viewtopic.php?f=4&t=22918 |
Page 1 of 1 |
| Author: | rich.zs [ Tue Aug 16, 2011 10:54 am ] |
| Post subject: | efi inlet onto zetec head, bolts too short. |
im doing a 2.0 zetec turbo conversion and im using the efi HO inlet with the injector plate ect but because of the added width from the injector plate the bolts to bolt the manifold on are too short, what bolts do i need to get ? thanks. rich |
|
| Author: | DarrenFsi [ Tue Aug 16, 2011 12:41 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
longer ones
|
|
| Author: | rich.zs [ Tue Aug 16, 2011 1:19 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
your clever aint you, will the standard bolts off a cvh fit or not ? |
|
| Author: | DarrenFsi [ Tue Aug 16, 2011 2:10 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
i dont think they would mate but not 100% get down to fords there about 60p new and you need ten of them i think 
|
|
| Author: | rich.zs [ Tue Aug 16, 2011 2:56 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
That's better help ain't it lol cheers lad |
|
| Author: | DarrenFsi [ Tue Aug 16, 2011 7:38 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
well all you said was there too short lol i couldnt help myself haha but yeah fords do em mate but make sure you take one down with same thread that you need cos ford near me have no idea when it comes to nuts n bolts lol |
|
| Author: | EvilDes [ Wed Aug 17, 2011 7:42 am ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
I think Darren was well within his rights to say longer ones  What other kind of answer were you expecting? M14 x 50mm?
|
|
| Author: | TANGO [ Wed Aug 17, 2011 9:01 am ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
If your thinking that was a sarcastic answer then it's probably a good thing that I didn't reply to it lol |
|
| Author: | rich.zs [ Wed Aug 17, 2011 1:53 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
well its just a bit of common sence that i needed to know more than just 'longer ones' my 2 year old neice could have told me that lol doing an engine conversion is stressful enough without sarcy comments when your trying to crack on with sorting everything out, im not trying to argue or be a dick you've helped me now and thanks for the help but it just would have been easier to just be a bit more helpful in the first place |
|
| Author: | meilack [ Wed Aug 17, 2011 1:57 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
did ford have the bolts? |
|
| Author: | rich.zs [ Wed Aug 17, 2011 4:13 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
I haven't had chance to go there yet will be going there tomorrow I'll let you know |
|
| Author: | james_rs [ Wed Aug 17, 2011 5:22 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
If they dont happen to have or be able to get some quick pm me im sure i have some. Many in fact! |
|
| Author: | rich.zs [ Fri Aug 19, 2011 9:46 am ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
fords had them but wanted 40 odd quid for them RIP OFFS so i told him to shove it and went round the corner to a tool place and he has loads there cost me 2.06p for 10 of them lol cheers anyway cookie |
|
| Author: | DarrenFsi [ Fri Aug 19, 2011 10:16 am ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
40 quid? wtf lol |
|
| Author: | rich.zs [ Mon Aug 22, 2011 1:13 pm ] |
| Post subject: | Re: efi inlet onto zetec head, bolts too short. |
and that was with 25% discount the robbing b*stards they wanted £30 for 9 exhaust studs...i swear the fords by me charge alot more for stuff than anywhere else its rediculous |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|