| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| Flywheel https://www.fiesta-si.com/forums/viewtopic.php?f=4&t=20789 |
Page 1 of 1 |
| Author: | fezziesi [ Sat Oct 16, 2010 10:24 am ] |
| Post subject: | Flywheel |
Does a 1.6 zetec flywheel go onto a cvh engine? Trying to find this information is hard, im after a cvh one but is proving hard to get! |
|
| Author: | will121 [ Sat Oct 16, 2010 6:06 pm ] |
| Post subject: | Re: Flywheel |
ive just compared the two flywheels, ones i have are same diameter and rear spacing and would expect same bolt pattern is both got 220mm clutch, only thing was Si one was about 1mm thicker towards the front and has the extra thickness at rear for the crank position sensor pickup |
|
| Author: | fezziesi [ Sun Oct 17, 2010 11:33 am ] |
| Post subject: | Re: Flywheel |
You dont fancy selling one do ya? |
|
| Author: | will121 [ Sun Oct 17, 2010 12:39 pm ] |
| Post subject: | Re: Flywheel |
the CVH one i have is from a escort XR3i think postage be a killer unless you local to Norfolk? |
|
| Author: | fezziesi [ Sun Oct 17, 2010 1:14 pm ] |
| Post subject: | Re: Flywheel |
How heavy is it? ill get a postage quote Shouldnt be too much |
|
| Author: | fezziesi [ Sun Oct 17, 2010 1:26 pm ] |
| Post subject: | Re: Flywheel |
Just weighed the one that came of my 1.1 engine and that is 7.2kg parcelforce want £15 postage roughly |
|
| Author: | will121 [ Sun Oct 17, 2010 2:56 pm ] |
| Post subject: | Re: Flywheel |
just been to take it off so can weigh it and there is a fair bit of wear on the face of it so its not the best |
|
| Author: | fezziesi [ Sun Oct 17, 2010 3:52 pm ] |
| Post subject: | Re: Flywheel |
Ah i see, its impossible to find one anywhere lol No problem mate, thanks for your help |
|
| Author: | james_rs [ Sun Oct 17, 2010 9:59 pm ] |
| Post subject: | Re: Flywheel |
parcel2go.com posted mine for about a tenner i think a cvh one will go on a zetec but im sure the bolt holes need enlarging by about a 1mm or something. the cvh ones are lighter i think too |
|
| Author: | fezziesi [ Mon Oct 18, 2010 5:31 pm ] |
| Post subject: | Re: Flywheel |
What an amazing site, soo cheap! |
|
| Author: | james_rs [ Mon Oct 18, 2010 8:44 pm ] |
| Post subject: | Re: Flywheel |
Yep, very good service from them too! |
|
| Author: | rs220bhp [ Tue Oct 19, 2010 9:20 pm ] |
| Post subject: | Re: Flywheel |
cvh will fit a zetec and as said needs the holes drilling to 11mm, is lighter than the zetec on by about 2kg iirc. Wouldnt fit a zetec one to a cvh as the holes will be to large for the bolts. |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|