†Ûi³ÿßrȬþ;
ob_start();
?>
†Ûi³ÿßrȬþ;
ob_start();
?>
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4767: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4769: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4770: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4771: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| breaking the bead on si 14" alloys https://www.fiesta-si.com/forums/viewtopic.php?f=4&t=18041 |
Page 1 of 1 |
| Author: | Jam [ Sat Nov 14, 2009 11:35 am ] |
| Post subject: | Re: breaking the bead on si 14" alloys |
what they want 45 quid in labour? or is that supply the tyres aswell?....if its just labour id be going somewhere else! , youll still have to pay tyre disposal and to have them balanced but your options for breaking the bead are. slide hammer (looks like a concrete breaker) sledge and wedge although your aim will need to be good! or a press. if it gets to that point its easier to take it to a branch of monkeyfit and get them to do it. steelies arent too bad to diy..but alloys are nice and soft and easily gouged by tools. how heavy was the vehicle you ran over it with?. and i am assuming you have changed a tubeless tyre before |
|
| Author: | will121 [ Sat Nov 14, 2009 4:09 pm ] |
| Post subject: | Re: breaking the bead on si 14" alloys |
removing tyres is a very difficult DIY job, firstly braking the bead but then leavering them off, picture from another forum on bead breaker but best done when no one else at home!!!
|
|
| Author: | cs detailing [ Sat Nov 14, 2009 4:57 pm ] |
| Post subject: | Re: breaking the bead on si 14" alloys |
Think about it, how is £45 alot ? To take the tyre off, fit a new tyre and then balance it ( most places charge £10 for just 1 wheel balancing ) £45 doesnt seem that much to do 4. As im pretty much sure that a tyre place wont fit another tyre without balancing it ! |
|
| Author: | cs detailing [ Sat Nov 14, 2009 10:44 pm ] |
| Post subject: | Re: breaking the bead on si 14" alloys |
You didnt say that in your first post Have you got a bench vice that the jaws open enough to clamp the tyre ? Thats what i used once. Then a crowbar and a block of rubber |
|
| Author: | cs detailing [ Sat Nov 14, 2009 11:13 pm ] |
| Post subject: | Re: breaking the bead on si 14" alloys |
screwdriver and claw hammer.... nice lol hammers arnt a good thing with me... i always seem to damage things lol |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|