��i���rȬ�;��i���rȬ�;[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4767: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4769: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4770: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4771: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
Fiesta-Si.com :: View topic - 1.25si running rough
Fiesta-Si.com
https://www.fiesta-si.com/forums/

1.25si running rough
https://www.fiesta-si.com/forums/viewtopic.php?f=4&t=17356
Page 1 of 1

Author:  strypus [ Tue Aug 25, 2009 5:51 pm ]
Post subject:  1.25si running rough

Hi All

Was stuck in traffic for 3 hours and somthing has happened to the car. when pulling away now it is realy sluggish im haveing to rev loads to get going seems ok when im doing over 40 its like i have to keep dipping the clutch when pulling away. Also on steep hills i now need to be in a lower gear than i used to be to make it up the hill. any ideas

THX

Wendell

Author:  onslack [ Wed Aug 26, 2009 9:02 am ]
Post subject:  Re: 1.25si running rough

welcome to fsi

i dont know that much info on the 1.25 zetec SE engines, but i'll give it a go :lol:

i maybe wrong but have you tried cleaning your MAF sensor? only other thing i can think of is mayeb your lambda sensor

are you able to get to a garage to get it on a diagnostic machine to see if that can pick up a fault? will save you alot of time and chasing your tail :thumbsup:

Author:  strypus [ Wed Sep 16, 2009 4:32 pm ]
Post subject:  Re: 1.25si running rough

Hi thxs for the reply

I hhave been told its the coil pack is this an easy job or a job for garage?

thxs

Author:  onslack [ Wed Sep 16, 2009 5:16 pm ]
Post subject:  Re: 1.25si running rough

if its anything like the coil pack on the MK3 zetec E Si's then it'll be easy to do yourself :chill:

Author:  strypus [ Thu Sep 17, 2009 5:54 pm ]
Post subject:  Re: 1.25si running rough

When you say easy how easy is that does it matter what order the ht leads are connected to the coil pack?

thxs

Author:  mattu101 [ Thu Sep 17, 2009 8:57 pm ]
Post subject:  Re: 1.25si running rough

Its very easy, a lot easier than a mk3 if that's possible as the engine bays a lot less cramped.

Yes they need to go in the correct order but you can always number them with tipp-ex and reference to paper, that's the way I first did it.

Then its just a case of removing the four set screws and putting in a new pack, I got one for 12 quid off ebay and it worked past the engine.

I have a spare ford one if wanted :thumbsup:

Page 1 of 1 All times are UTC [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/