hi guys need your help is this setup that i have done for the induction kit right or is it a total shambles lol
would appreciate your views thanks
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| need help!! induction kit viper https://www.fiesta-si.com/forums/viewtopic.php?f=4&t=17051 |
Page 1 of 1 |
| Author: | tg2790 [ Wed Jul 22, 2009 10:09 pm ] |
| Post subject: | need help!! induction kit viper |
hi guys need your help is this setup that i have done for the induction kit right or is it a total shambles lol would appreciate your views thanks
|
|
| Author: | tg2790 [ Wed Jul 22, 2009 10:22 pm ] |
| Post subject: | Re: need help!! induction kit viper |
it is on fiesta mk4 1.3 ghia its a viper induction kit |
|
| Author: | Percy [ Wed Jul 22, 2009 11:27 pm ] |
| Post subject: | Re: need help!! induction kit viper |
I thought the vipers where enclosed with a feed? |
|
| Author: | will121 [ Wed Jul 22, 2009 11:32 pm ] |
| Post subject: | Re: need help!! induction kit viper |
if its a sealed viper filter would think the flexi hose a bit long, would be better with the silicon hose angle from the throttle body - MAF - Viper can between engine and battery or bit further forward and then the cold air flexi hose feeding the filter with cold air from the valance area, only pic i can find at mo. |
|
| Author: | tg2790 [ Wed Jul 22, 2009 11:41 pm ] |
| Post subject: | Re: need help!! induction kit viper |
hmm its weird because it gives out very good performance compared to before, better throttle response and quicker accelaration and mid range speed and noise has improved as well but have probably fitted it wrong its an odd one lol |
|
| Author: | Percy [ Thu Jul 23, 2009 12:39 am ] |
| Post subject: | Re: need help!! induction kit viper |
What will posted is what I was expecting. |
|
| Author: | Ry [ Thu Jul 23, 2009 7:59 am ] |
| Post subject: | Re: need help!! induction kit viper |
Is there another pipe after the enclosed filter? you normally route it to a foglight and replace it with the Si's, create a hole or route it under the bonnet. Though if you're intake after the viper is where you fog light is, your car is low and you live in a very dodgy area when it rains and there's lot of puddles and what not, try investing in a Air Bypass Valve as well. |
|
| Author: | tg2790 [ Thu Jul 23, 2009 11:17 am ] |
| Post subject: | Re: need help!! induction kit viper |
hi guys thanks for the help ive found out what the problem is ive put the cold air feed pipe where the standard hose pipe should be and the cold air feed pipe needs to go at the other end of the viper kit only thing is is that im not sure where i should lead the cold air feed pipe to? |
|
| Author: | will121 [ Thu Jul 23, 2009 12:30 pm ] |
| Post subject: | Re: need help!! induction kit viper |
that sounds better did the original air box have a standard cold air feed pipe, on a Si think it goes towards a area beside the radiator behind the bumper height ish
|
|
| Author: | tg2790 [ Thu Jul 23, 2009 2:58 pm ] |
| Post subject: | Re: need help!! induction kit viper |
erm no i dont think so and yea i had a rough idea it would be fed to the grill area |
|
| Author: | tg2790 [ Thu Jul 23, 2009 2:59 pm ] |
| Post subject: | Re: need help!! induction kit viper |
i was wondering if i cleaned my standard hose pipe out will it make much difference in performance if it has been cleaned? |
|
| Author: | Percy [ Thu Jul 23, 2009 3:02 pm ] |
| Post subject: | Re: need help!! induction kit viper |
It won't do any harm to clean it, might aswell if you have got the chance. |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|