i have but i cant figure out what drive belt i need!
im using the si alternator mount so if any 1 know which 1 i need please reply as im now nearing the end of my project
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| who has fitted a 2l without PAS? https://www.fiesta-si.com/forums/viewtopic.php?f=4&t=17044 |
Page 1 of 2 |
| Author: | john_d [ Wed Jul 22, 2009 4:04 pm ] |
| Post subject: | who has fitted a 2l without PAS? |
i have but i cant figure out what drive belt i need! im using the si alternator mount so if any 1 know which 1 i need please reply as im now nearing the end of my project
|
|
| Author: | Percy [ Wed Jul 22, 2009 4:13 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
Should be the 1.6 Si one. If you think about it when you do a 2.0 conversion you are basically just replacing the 1.6 block with a 2.0 block, pretty much everything else around it remains '1.6' as such. |
|
| Author: | john_d [ Wed Jul 22, 2009 4:15 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
nope, the si has the power steering wheel on the drive belt, i dont, i only have the water pump. crank pulley and alternator. ps i started with a 1.1hcs |
|
| Author: | Percy [ Wed Jul 22, 2009 4:22 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
I see the problem. It been a few years since i had my 2.0 so just trying to remember where everything went. Not sure the best way, of course a shorter one would do, but which is a good question. Is it not an option to fit part of the PAS system just so the pulley is there? |
|
| Author: | john_d [ Wed Jul 22, 2009 4:27 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
| Author: | Percy [ Wed Jul 22, 2009 4:33 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
Yeah you can see just fitting the pump would solve the problem, as you would imagine most people just do the conversion on a 1.6 so its a none issue. Maybe somebody else will have a better plan. |
|
| Author: | elPaulio [ Wed Jul 22, 2009 7:12 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
hi there, best place to look would be kit car sites as they use the 2 litre silver top without power steering all the time! hope that gives you a shove in the right direction! I would look it up but I'm on my phone just now! paul |
|
| Author: | happypaul [ Thu Jul 23, 2009 11:27 am ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
XR2i 1800 Zetec NON PAS engine mount, and belt will be perfect. I didnt have pas in the pickup so I routed the pas pumps pipes around to itself so it just ran fluid round itself constantly.. worked fine, although abit pikey. |
|
| Author: | john_d [ Thu Jul 23, 2009 11:36 am ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
does that lok like this? 
|
|
| Author: | happypaul [ Thu Jul 23, 2009 11:48 am ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
| Author: | john_d [ Thu Jul 23, 2009 12:59 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
| Author: | john_d [ Thu Jul 23, 2009 6:40 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
| Author: | happypaul [ Thu Jul 23, 2009 11:40 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
Sorted
|
|
| Author: | john_d [ Fri Jul 24, 2009 6:38 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
the 1 i bought was 1000mm but was a fraction too small, the next 1 they do he said was a 130, im guessing he means a 1130, which is 130mm longer, i think that may be a tad too long  pick it up tomorrow. |
|
| Author: | john_d [ Sat Jul 25, 2009 10:03 am ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
well i got my new 1, when he said 130 he meant 13mm, but i know for a fact that's still be too small so opted for a 1075, an extra 75 may sound like a lot but i recon (and hope) that any additional slack is taken up by the tensioner also looking to botch together some coolant pipes, get the fuel lines connected to the tank and try and start her for the 1st time  some how i think that for whatever reason she wont but im hell bent on having her running today. |
|
| Author: | dougxr2i [ Sat Jul 25, 2009 10:33 am ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
have you tried the xr2i 1.8 zetec drivebelt that have doesn't power steering |
|
| Author: | john_d [ Sat Jul 25, 2009 3:38 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
| Author: | elPaulio [ Sat Jul 25, 2009 7:46 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
the 1.8 zetec is identical to the 1.6 zetec in the si so getting the belt for the xr2i without pas will fit a treat as that's what it's for. paul |
|
| Author: | john_d [ Sat Jul 25, 2009 7:50 pm ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
and ur positive of this? its the bracket om not sure about. if i buy 1 and it doesnt fit will u refund me the money? 
|
|
| Author: | happypaul [ Sun Jul 26, 2009 9:31 am ] |
| Post subject: | Re: who has fitted a 2l without PAS? |
I tried an XR2i non pas belt. Didnt fit with the zetec pas mounting. Hence why Ive ran 6 months with the pas pump still in place routing fluid around itself to stop it ceizing up. |
|
| Page 1 of 2 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|