5mm spacers on the front, you might not need them on the back, but if you did i'd say probs 3mm
And all wheels need spigot rings, however you can live without them. I don't have any on my car.
Hope this helps
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| *yawn* wheel question *yawn* https://www.fiesta-si.com/forums/viewtopic.php?f=13&t=21683 |
Page 1 of 1 |
| Author: | andyleesy [ Sat Feb 12, 2011 10:52 pm ] |
| Post subject: | *yawn* wheel question *yawn* |
Ok, time for the obligatory wheel question, they do come round once in a while, but i can't get my head around this... Ok my car has: 4x108 Studs, 35 to 42 Offset and 63.4 Hub Bore.... and i wanted to fit: 4x108, 30 Offset, 65 Hub Bore a) Would I need to space them out 5mm - 7mm or something? b) Would I need spigot rings, or because they are exact stud fitment would nothing be required? Cheers Andy |
|
| Author: | stainlessmole [ Sat Feb 12, 2011 10:55 pm ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
5mm spacers on the front, you might not need them on the back, but if you did i'd say probs 3mm And all wheels need spigot rings, however you can live without them. I don't have any on my car. Hope this helps
|
|
| Author: | andyleesy [ Sat Feb 12, 2011 11:03 pm ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
excellent, cheers mate 
|
|
| Author: | bensouthport [ Sun Feb 13, 2011 11:51 pm ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
what are spigot rings may i ask? |
|
| Author: | Jam [ Tue Feb 15, 2011 9:03 pm ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
if you put a 5mm spacer on a wheel with an offset of 30. your offset is then 25. if your using spacers generally the figure goes down unless your dealing in wheels with a - offset. (deep dish rear drive comes to mind) yet effectively your clearance goes up. depending on the width of the rim. they might bolt right on, for 1.6mm so .8mm all the way round...i really cant see that spigot rings are a neccesity. HTH Jam. |
|
| Author: | stainlessmole [ Tue Feb 15, 2011 10:54 pm ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
| Author: | bensouthport [ Tue Feb 15, 2011 11:36 pm ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
ahh right thats interesting. do they by any chance space the wheels out slightly or not? i have some on the alloys i bought (ford fitment) and they stick out past the arch... hence why i want to sell them! thanks mole |
|
| Author: | stainlessmole [ Wed Feb 16, 2011 12:28 am ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
Nah it's only to position the wheel |
|
| Author: | bensouthport [ Wed Feb 16, 2011 11:47 am ] |
| Post subject: | Re: *yawn* wheel question *yawn* |
rytio, cheers. |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|