| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| Gauge Mod https://www.fiesta-si.com/forums/viewtopic.php?f=13&t=21054 |
Page 1 of 1 |
| Author: | InSane [ Sun Nov 28, 2010 10:01 am ] |
| Post subject: | Gauge Mod |
Hi i am going to put a water temp Gauge but i need to order the Water Temperature Sensor adaptor so would like some to tell me if they can inner dimensions of the top hose by radiatoras i am not shure of size to order Adapters size: 32mm  i hopeI also order a volt gauge but i am also thinking of oil temp Gauge but not shure what i need as i guess its will be connected to the engine some how |
|
| Author: | rs220bhp [ Sun Nov 28, 2010 10:13 pm ] |
| Post subject: | Re: Gauge Mod |
As said in the PM mate you can fit the new sensor in place of the old one so no need to cut the top hose etc. I can supply you one of these if you want to put the gauges in to keep the dash looking standard. Have black and grey ones but cant use them with my cage  it takes 2 52mm gauges |
|
| Author: | stainlessmole [ Sun Nov 28, 2010 10:22 pm ] |
| Post subject: | Re: Gauge Mod |
OOh you need to tell me what is needed to fit rst counters, obvi i would need the clocks.. but what else? New speedo cable, the thing that the speedo goes into on the gearbox? 
|
|
| Author: | InSane [ Sun Nov 28, 2010 10:34 pm ] |
| Post subject: | Re: Gauge Mod |
| Author: | rs220bhp [ Mon Nov 29, 2010 10:19 am ] |
| Post subject: | Re: Gauge Mod |
| Author: | InSane [ Mon Nov 29, 2010 6:47 pm ] |
| Post subject: | Re: Gauge Mod |
let me know when you are a round mate i can pick it up this week |
|
| Author: | rs220bhp [ Mon Nov 29, 2010 7:06 pm ] |
| Post subject: | Re: Gauge Mod |
| Author: | InSane [ Mon Nov 29, 2010 7:46 pm ] |
| Post subject: | Re: Gauge Mod |
thxs for that letme know the cost of the hose and the dials holders mate and how many you have i guess i will paint them so if you have to blacka and a gray just lem me no what you have |
|
| Author: | stainlessmole [ Mon Nov 29, 2010 8:36 pm ] |
| Post subject: | Re: Gauge Mod |
oh ok lol... i guess the timing is in the clock then. The reason why i asked is because RST dials go up to 150mph, and standard 140mph. :s |
|
| Author: | rs220bhp [ Mon Nov 29, 2010 8:50 pm ] |
| Post subject: | Re: Gauge Mod |
Yeah the timing/mechanics in the clock will be different. Gear box/speed sensor are the same on models. Need a pair of clocks??? |
|
| Author: | InSane [ Mon Nov 29, 2010 8:58 pm ] |
| Post subject: | Re: Gauge Mod |
ok what night are you free and how much |
|
| Author: | stainlessmole [ Mon Nov 29, 2010 9:05 pm ] |
| Post subject: | Re: Gauge Mod |
Yeah, all i want is the speedometer - 150mph. Because rst rev counter will be incorrect due to it being electrical and going on a zetec engine rather than cvh, and it would be much cheaper to send it too. What's the mileage? Or do you know how to change it without actually moving the numbers lol
|
|
| Author: | rs220bhp [ Mon Nov 29, 2010 9:10 pm ] |
| Post subject: | Re: Gauge Mod |
Rev gauge will be the same mate so it would be easier to do a complete swap of the units. can send just the clock if you want just that bit but would want the same as the complete set. |
|
| Author: | stainlessmole [ Mon Nov 29, 2010 11:05 pm ] |
| Post subject: | Re: Gauge Mod |
Ill have the whole thing then haha |
|
| Author: | rs220bhp [ Wed Dec 01, 2010 6:58 pm ] |
| Post subject: | Re: Gauge Mod |
Send me a PM we can discuss instead of taking this thread off topic |
|
| Author: | stainlessmole [ Wed Dec 01, 2010 8:01 pm ] |
| Post subject: | Re: Gauge Mod |
oh yeah my bad lol |
|
| Author: | InSane [ Sun Dec 05, 2010 4:12 pm ] |
| Post subject: | Re: Gauge Mod |
Ok i decided to put the Gauges in the centre console so i made the fixing plate and put the Gauges in and also wire them up when i have a good day with the weather..should only need a bit of a trim to get it to fit  
|
|
| Author: | Dave5300 [ Mon Dec 06, 2010 10:30 pm ] |
| Post subject: | Re: Gauge Mod |
looks really good mate 
|
|
| Author: | InSane [ Tue Dec 07, 2010 6:53 am ] |
| Post subject: | Re: Gauge Mod |
i am just waiting for a good day to fit them now
|
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|