†Ûi³ÿßrȬþ;
ob_start();
?>
†Ûi³ÿßrȬþ;
ob_start();
?>
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4767: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4769: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4770: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4771: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| alloy help https://www.fiesta-si.com/forums/viewtopic.php?f=13&t=19327 |
Page 1 of 1 |
| Author: | rob_fiesta [ Mon Apr 05, 2010 10:14 pm ] |
| Post subject: | alloy help |
Hi all Right i have droped the car 40mm will i be able to fit 16" alloys with out them rubbing Thanks Rob |
|
| Author: | Elward [ Mon Apr 05, 2010 10:49 pm ] |
| Post subject: | Re: alloy help |
not unless you do some arch work i think |
|
| Author: | rob_fiesta [ Mon Apr 05, 2010 11:09 pm ] |
| Post subject: | Re: alloy help |
ow stuff it then 13" will stay
|
|
| Author: | sjoyce666 [ Mon Apr 05, 2010 11:13 pm ] |
| Post subject: | Re: alloy help |
Should get away with it if you run 195/40/16 tyres I had my Magnesium 16's on my Yellow Si lowered 40mm with 195/45/16 tyres and they didnt catch even on full lock but they were only 6.5J whereas alot of aftermarket alloy wheels will be a little wider than this Scott |
|
| Author: | rob_fiesta [ Mon Apr 05, 2010 11:27 pm ] |
| Post subject: | Re: alloy help |
if i did go 16" it would be mondeo |
|
| Author: | Chris [ Tue Apr 06, 2010 12:41 am ] |
| Post subject: | Re: alloy help |
I'm not proud of my very old so and the 17 inch wheels, but I will mention it this once... I had 195/45/15 and I would say there was about 30-35mm gap between the arch (as in the outer bit, not the inside directly above the tyre) and the tyre. so you might get away with it. My tyres did scrape the plastic engine guards on full lock though. 15's would be an easier upgrade. Wouldn't soil the accelorations and handling so much either. |
|
| Author: | Percy [ Tue Apr 06, 2010 1:01 am ] |
| Post subject: | Re: alloy help |
In diameter terms: 195/45/15 = 556mm 195/40/16 = 562mm 195/45/16 = 582mm Hope this helps. |
|
| Author: | rob_fiesta [ Tue Apr 06, 2010 10:33 am ] |
| Post subject: | Re: alloy help |
cheers might just go 15 like chris said cheers for the diameter terms |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|