tell me how it goes then
and il judge whether to do mine depending on how well yours goes
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| rear arch lips! https://www.fiesta-si.com/forums/viewtopic.php?f=13&t=19221 |
Page 1 of 2 |
| Author: | bensouthport [ Sun Mar 21, 2010 9:16 pm ] |
| Post subject: | rear arch lips! |
i know these are a big problem on si's. with the rusting especially. the rubbing on the tires which comes with it (edge of my tire is goudged to say the least). ive had a couple of other links not specific to this but people have said about bashing them and cutting them off all together. just wondering what everyone else does with them because i want rid of them before i lower it and get new rims!? thanks chaps. |
|
| Author: | stainlessmole [ Sun Mar 21, 2010 10:11 pm ] |
| Post subject: | Re: rear arch lips! |
You can get a heat gun and a small rubber mallet and slowly bend the lip around. That is probably the easiest way if done right |
|
| Author: | bensouthport [ Sun Mar 21, 2010 10:17 pm ] |
| Post subject: | Re: rear arch lips! |
yeh ive been advised to do that. what have you done with yours? or havnt you? |
|
| Author: | stainlessmole [ Sun Mar 21, 2010 11:16 pm ] |
| Post subject: | Re: rear arch lips! |
Not yet... lol |
|
| Author: | bensouthport [ Mon Mar 22, 2010 12:47 am ] |
| Post subject: | Re: rear arch lips! |
tell me how it goes then and il judge whether to do mine depending on how well yours goes
|
|
| Author: | stainlessmole [ Mon Mar 22, 2010 11:50 am ] |
| Post subject: | Re: rear arch lips! |
Haha i hope well, i just had my arches done about a year ago. So they are rust free! I'm gunna wait until i put my XR/RS skirts and arches on first i think. It does need to be done though! Because with 16" Mondy zetecs (R16 205 45) and lowered 35/40mm it's gunna scrape with a feather in the back! lol |
|
| Author: | bensouthport [ Tue Mar 23, 2010 1:57 am ] |
| Post subject: | Re: rear arch lips! |
well good luck! haha, bet it looks tidy though  atleast you have a legitimate reason for scraping. mine does with orig 14"s with bugger all in the back
|
|
| Author: | - Danny Boy - [ Thu Mar 25, 2010 6:26 pm ] |
| Post subject: | Re: rear arch lips! |
On my old 1.3, i didnt use a heat gun, just hit the inside of the lip around with a rubber mallet, paint didnt even crack  lol
|
|
| Author: | bensouthport [ Tue Mar 30, 2010 7:15 pm ] |
| Post subject: | Re: rear arch lips! |
il try that but if it cracks im blaming it on you danny boy! |
|
| Author: | happypaul [ Tue Mar 30, 2010 9:33 pm ] |
| Post subject: | Re: rear arch lips! |
Jack car up safely, Remove wheel, Take your grinder and cut the lip off a few mm at a time around the top of the lip, and the bumper part, and see if it rubs then. Stuff folding it, it'll only gather water and rust out anyway, so just cut the lip abit |
|
| Author: | bensouthport [ Tue Mar 30, 2010 9:42 pm ] |
| Post subject: | Re: rear arch lips! |
and then kurust and hammerite it? thanks happy paul, id rather try that to be fair |
|
| Author: | happypaul [ Wed Mar 31, 2010 7:17 pm ] |
| Post subject: | Re: rear arch lips! |
You could touch the cut edge up with abit of hammerite with a small brush to keep it from the elements yeah Its better than messing around bashing the arch lips on, can cause more issues |
|
| Author: | TANGO [ Wed Mar 31, 2010 7:24 pm ] |
| Post subject: | Re: rear arch lips! |
bashing it with a hammer would be iffy, could cause the panel to ripple further up, and as paul said water can collect there, not good, just chop the fookers off, lol |
|
| Author: | Jam [ Wed Mar 31, 2010 8:06 pm ] |
| Post subject: | Re: rear arch lips! |
i didnt manage to ripple mine lol..no heat and a hide mallet when its nearly there...sikaflex the seam your bashing up..nice seal to stop the crap getting in..finish beating and use a brush with thinners to spread the excess that came out. i know paul went at his with a grinder. but we both covered up the butcherism with XR kits...and pauls was more butchered than mine lol |
|
| Author: | bensouthport [ Wed Mar 31, 2010 8:30 pm ] |
| Post subject: | Re: rear arch lips! |
ha! i dont want to risk the paint rippling at all, rather grind them down and as you said, whack an xr2i kit on. was my plan anyway. thanks for the advice though (Y) i let you know how it goes anyway as i should be doing it soon. |
|
| Author: | happypaul [ Wed Mar 31, 2010 9:54 pm ] |
| Post subject: | Re: rear arch lips! |
If your going to be fitting skirts/arches anyway, you can cut not just the lip off, but go a few mm above the arch, allows for bigger wheels with a good drop
|
|
| Author: | bensouthport [ Wed Mar 31, 2010 10:40 pm ] |
| Post subject: | Re: rear arch lips! |
i think i will do that happypaul  how much bigger though? your black alloys on your pick up, were they fox evo's? im thinking of going to 16" |
|
| Author: | happypaul [ Thu Apr 01, 2010 12:15 pm ] |
| Post subject: | Re: rear arch lips! |
I fitted 16's with 45 profile tyres with a 60mm all round drop perfectly fine. I also fitted 16's with a 40 profile with 205 width tyre on a Sierra fitment wide as fook set of wheels, on a 80mm rear 70mm front drop, and managed to pull that off |
|
| Author: | Jam [ Thu Apr 01, 2010 12:32 pm ] |
| Post subject: | Re: rear arch lips! |
along with the kit several times on the pickup lol |
|
| Author: | happypaul [ Thu Apr 01, 2010 12:58 pm ] |
| Post subject: | Re: rear arch lips! |
The kit only fell off the RS due to mudflaps The kit only fell off the pickup because 1) I cut too much off 2) It was actually the metal that came off 
|
|
| Page 1 of 2 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|