†Ûi³ÿßrȬþ;
ob_start();
?>
†Ûi³ÿßrȬþ;
ob_start();
?>
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1056: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions_content.php on line 696: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4767: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4769: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4770: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4771: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:19)
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| 2.0 conversion. https://www.fiesta-si.com/forums/viewtopic.php?f=13&t=18635 |
Page 1 of 1 |
| Author: | will87 [ Mon Jan 18, 2010 5:13 pm ] |
| Post subject: | 2.0 conversion. |
Finally got a 2.0 mondeo , just checked the ECU and its OWLS. i was just wondering if i can just plug in a DESK, DEWY, DEEP and it will work. or will i need to change anything else? also do i use the 1.6 Throttle Position Sensor on the 2.0 throttle body? another one, can you get the engine and box out together or will you need to take the box off first ect.. Cheers. |
|
| Author: | onslack [ Tue Jan 19, 2010 10:28 am ] |
| Post subject: | Re: 2.0 conversion. |
check these 2 thread bussy, they have all the info you need viewtopic.php?f=16&t=122&start=0 viewtopic.php?f=3&t=4855&start=0 DEEP, DESK, DEWY ecu will plug straigh into the 1.6 16v Si Loom, just use all the sensors etc off your 1.6 engine i'd just use your 1.6 TPS as you know it works, iirc i had a 2.0 one on my fez and it seemed too work ok, it was just upside down from memory disconnect eveything from the engine and make sure its ready to drop then just drop the engine and box together from under the car, lift the shell up and over it |
|
| Author: | will87 [ Fri Jan 22, 2010 2:15 am ] |
| Post subject: | Re: 2.0 conversion. |
thanks
|
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|