what about megasquirt?
DTA, omex etc are good too
| Fiesta-Si.com https://www.fiesta-si.com/forums/ |
|
| aftermarket ecu https://www.fiesta-si.com/forums/viewtopic.php?f=1&t=6404 |
Page 1 of 1 |
| Author: | Mouse [ Sat Apr 14, 2007 11:03 pm ] |
| Post subject: | aftermarket ecu |
does any one know where i can get an aftermarket ecu ? iv been looking at emerald ecu's but if any one has any info on aftermarket ecu's like names and what there like it would be most appreciated i also have a laptop with maga jolt v2 on it that i can plug in to the car (ecu well for most aftermarket ones) so if the ecu comes with a program i could load it to the laptop and mess around with it he he he |
|
| Author: | xmadxmoex [ Sat Apr 14, 2007 11:56 pm ] |
| Post subject: | |
what about megasquirt? DTA, omex etc are good too
|
|
| Author: | saqmaster [ Sun Apr 15, 2007 12:55 am ] |
| Post subject: | |
http://www.megatuned.com 
|
|
| Author: | Mouse [ Sun Apr 15, 2007 6:07 pm ] |
| Post subject: | |
i thought mega squirt was just for fuel or is it ? saqmaster;- iv had a looky at your site so what do you recomend  and how long would it take to set up lol
|
|
| Author: | saqmaster [ Sun Apr 15, 2007 6:08 pm ] |
| Post subject: | |
Nope, Megasquirt does it all... what's the spec. you need an aftermarket ECU for? |
|
| Author: | Mouse [ Sun Apr 15, 2007 6:19 pm ] |
| Post subject: | |
erm newman fast road cams (not set up properly yet hehe) ported inlet manifold (1.8), to the head and sandwich plate, casts ground off from inlet manifold and head ports, lightened and balanced fly wheel (1.6 si) , crank polished and balanced, k&n 57i induction kit, de-cat, bb2 i think exhaust de-cat back lol oh and the 2.0l, ecu throttle body and air flow meter, im sure there some thing else but i cant remember |
|
| Author: | saqmaster [ Sun Apr 15, 2007 6:21 pm ] |
| Post subject: | |
Probably not worth the cost to be honest fella.. the current map in your 2 litre ECU won't be too far wrong for what you've got there! |
|
| Author: | Mouse [ Sun Apr 15, 2007 6:23 pm ] |
| Post subject: | |
ar reet doh! lol cheers any way looks like iv got a hard task trying to set the cams up properly then and sort out any other problems that crop up |
|
| Author: | saqmaster [ Sun Apr 15, 2007 6:24 pm ] |
| Post subject: | |
Do Newman give you Lift@TDC figures, like Kent do? |
|
| Author: | Mouse [ Sun Apr 15, 2007 9:51 pm ] |
| Post subject: | |
they give the lift and that but not the what i call timing bit like 10 or 8 degrees witch is poo unless im reading it wrong, but iv been searching for a fue days now so i might just fax them at work and see what i get this is what iv got so far for-- FORD ZETEC PH2 CAM forz/260/400 full lift IN. ATDC EX. BTDC 110 110 IN OPEN EX CLOSED 18-58 58-18 |
|
| Author: | saqmaster [ Sun Apr 15, 2007 9:52 pm ] |
| Post subject: | |
Ask them for lift@tdc figures.. easiest to time in.. |
|
| Author: | Mouse [ Sun Apr 15, 2007 9:59 pm ] |
| Post subject: | |
OOPS must of pressed submit before i should of lol ass on my above post |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|